Date: Fri, 9 Dec 2005 11:14:19 -0600 From: "Stephen Hicks, N5AC" Subject: MARS MOD DISCOVERED OK - here's an out-of-band mod that does TX from 0-54, 118-173, 400-470. 1. Remove CPU/dsp unit by unscrewing two silver screws holding it down (the silver box on the top of the radio with copper taped sides) and pull up. 2. Locate four shift registers and bank of diodes - shift registers are 4094's. There are two next to each other and then a couple more. We'll call the two stacked the "left" ones 3. The "left" shift register if looking from the front of the radio is the target. 4. Locate bank of SMT diodes (silver with "K" on top on one side) in front of the target shift register. They are in two columns, "left" and "right" 5. Unsolder one side of the second diode from the front on the left and lift up one side (or remove, slip to the side, whatever turns you on) I've uploaded a new photo with a picture as well (tv_mars.jpg) with both mods clearly illustrated. Steve ========================================================================= Date: Fri, 09 Dec 2005 19:43:20 -0000 From: "kb6muz" Subject: Re: MARS MOD DISCOVERED If you look closely at item number 3 (the shift register), the TV mod is located near/in line with the middle shift register, while the MARS mod is in line with the left shift register. I had to read this a few times myself, and look at the pictures ;-) --- In ic7000@yahoogroups.com, Urantian wrote: Hi Steve, This appears to be the same instructions as you sent for the TV mod. Does the mod handle both the TV and MARS/CAP? ---Michael, AE6QC ========================================================================= Date: Thu, 8 Dec 2005 16:55:27 -0600 From: "Stephen Hicks, N5AC" Subject: TV MOD DISCOVERED .... I couldn't wait to get a soldering iron to the inside of my new radio -- I have located the TV restore mod. Will this end the discussion on v-chip and legalities (please)? 1. remove CPU/dsp unit by unscrewing two silver screws holding it down (the silver box on the top of the radio with copper taped sides) and pull up. 2. locate four shift registers and bank of diodes - shift registers are 4094's. There are two next to each other and then a couple more. We'll call the two stacked the "left" ones 3. The "middle" shift register if looking from the front of the radio is the target. 4. Locate bank of SMT diodes (silver with "K" on top on one side) in front of the target shift register. They are in two columns, "left" and "right" 5. Unsolder one side of the second diode from the front on the left and lift up one side (or remove, slip to the side, whatever turns you on) I'll try to have some pictures here shortly. Also I have made some other mods that I don't think are critical, but I will be verifying this soon. I'm hunting for MARS mod also . let me know if any of you have this. Steve, N5AC ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Stephen Hicks, N5AC, AFA4SH EM13qc 469-576-7488 cell ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ========================================================================= Date: Thu, 8 Dec 2005 21:38:10 -0500 From: "James F. Boehner, MD" Subject: Re: TV MOD DISCOVERED .... Steve, I have a picture made up that details the mod-Please send me your e-mail address, and I'll send it to you to check over, and then submit to Adam for his ICOM page. When the MARS mod is found, I can add it to the picture. Also, this picture details the USA (#05) diode configuration. The mod works great-but to remove the CPU/DSP unit, I had to remove three silver screws rather than two. Thanks again for your experimentation and success! '73 de Jim N2ZZ ========================================================================= Date: Thu, 8 Dec 2005 09:07:01 -0800 (PST) From: Urantian Subject: Word from Icom on DTMF As Adam already stated, the HM-154T can be used for DTMF. To satisfy my desire for confirmation, I wrote to Icom, and received the following reply. ---Michael, AE6QC ============== You are correct. The IC-7000, with the supplied microphone, does not support real time DTMF. So far, none of Icom's HF radios have had the option for direct DTMF entry with their supplied microphones. If you wish to have the ability to enter DTMF codes directly from the microphone, real time, you will need to use the HM154T microphone. This is the same way that you could use DTMF on the 706 series radios or any of our other current HF radios. Kevin McClinton, W7JRL Technical Support Representative ICOM America, Inc. 2380 116th Ave. NE Bellevue, WA 98004 ========================================================================= Date: Wed, 7 Dec 2005 15:51:22 -0500 (EST) From: Doug Faunt N6TQS +1-510-655-8604 Subject: Re: DTMF Mic for the IC-7000 Thread-index: AcX7atKojWMhfM9YRjeSAlVANBXGgA== From: Adam Farson Date: Wed, 07 Dec 2005 12:14:40 -0800 To all group members concerned about DTMF on the IC-7000: I am informed that the Icom HM-154T DTMF microphone will work correctly with the IC-7000. IC-7000 owners requiring DTMF keysending should connect the HM-154T to the radio instead of the stock HM-151. The HM-154T will not support the mic-based control functions of the HM-151 supplied with the IC-7000. It is our fervent hope that this will put the DTMF thread to rest (at least for a while.) Well, mostly. Are the schematics for the HM-151 and the HM-154T available? It might be possible to add the functionality of the one to the other, with that information. 73, doug ========================================================================= Date: Fri, 9 Dec 2005 14:53:04 -0600 From: "Stephen Hicks, N5AC" Subject: RE: MARS MOD... Folks, the two sets of instructions look virtually identical, but the diode for MARS is on the LEFT set of diodes and the TV is on the middle set of diodes. Look at the update picture called tv_mars.jpg in the files section. Steve, N5AC ========================================================================= Date: Fri, 9 Dec 2005 19:36:10 -0500 From: "James F. Boehner, MD" Subject: Re: MARS MOD... To all, I have uploaded a high resolution picture of the shift registers/diodes with both the TVRO and MARS mods detailed, per the information provided to us by Stephen, N5AC. I put the full file in the files section, and uploaded the picture to the photo section of this group. The file name is TVRO-MARS_MOD.jpg. I did not put the "credit" line in the file, as I do not know if Stephen wants it in there. Stephen, if you want a credit line in the photo, I will be more than happy to add it. We all thank you for your experimentation and success! Just remember that the DSP/CPU unit must be removed in order to expose the board as seen in the photo. My unit required that three silver screws be removed. One note to all, I have modded almost every rig I own. I have not caused any disasters, but I worry every time I do a mod. These diodes are 1 mm in size. If you have any doubts about being able to do these mods, please consider having a service technician do them for you. As far as whether to just "raise a leg" of the diode or remove it, I think you have to be very good just to raise a leg. I'm able to do it occasionally, but I tend to remove them, put them on a small piece of Scotch tape, and put the tape with the diode somewhere in the supplied Owners manual, should it ever need to be reversed. '73 de Jim N2ZZ ========================================================================= Date: Fri, 9 Dec 2005 19:52:11 -0600 From: "Stephen Hicks, N5AC" Subject: RE: MARS MOD... I generally loose anything that is not tied down, so I generally unsolder the device and then scoot it to the side, leaving one pad soldered and the other resting on a part of the silk screen that is non-conducting. Not that the diodes are polarized and are marked. Be sure if you decide to reinstall, etc. that you put it in the right direction. Steve, N5AC ========================================================================= Date: Fri, 9 Dec 2005 21:10:24 -0500 From: "James F. Boehner, MD" Subject: Re: MARS MOD DISCOVERED And now for even more good news- The MARS mod does not affect the Auto Repeater Splits on 2m and 440! They still work! ICOM, good thinking! '73 de Jim N2ZZ ========================================================================= Date: Fri, 9 Dec 2005 20:20:51 -0800 (PST) From: Thomas McDuffie Subject: Re: MARS MOD DISCOVERED Except not all frequencies do Auto Repeater offset. Icom has not fixed a problem that is in many radios. Dial in 147.915. It should give a minus sign. No such luck. ========================================================================= Date: Sat, 10 Dec 2005 00:11:10 -0500 From: "James F. Boehner, MD" Subject: TVRO Activation Press and hold in the top left knob for greater than 1 second. Change the channel with the lower left knob. '73 de Jim N2ZZ ----- Original Message ----- From: "Fred" To: Sent: Friday, December 09, 2005 11:51 PM Subject: [IC-7000] Re: More Photos >I performed the mod and verified that the MARS portion works. > > I also performed the TV mod but can't figure out which > buttons to press to enable it. How does one select the TV mode? > > -fred ========================================================================= Date: Sat, 10 Dec 2005 00:11:56 -0500 From: "Jack Colton" Subject: RE: Re: More Photos Push and hold [AF(SET)] for 1 sec. to turn the TV mode ON. . Push and hold [AF(SET)] for 1 sec again to exit the TV mode. Rotate [M-ch] (inner) control to select the desired TV channel. . [Y(BAND)]/[Z(BAND)] keys also select the TV channel. . The popup indicator appears and shows the selected channel number. (The popup indicator can be turned OFF in the display set mode. p.128) Push [P.AMP/ATT] momentarily to turn the preamp ON and OFF; push and hold for 1 sec. to turn the 12 dB attenuator ON. .The popup indicator, " " or " ," appears when the preamp is ON or attenuator is ON, respectively. (The popup inidicator can be turned OFF in the display set mode. ) .Each channel can store the preamp or attenuator ON/OFF conditions independently. . Only one of these functions can be activated at a time. Rotate [AF] to set a suitable audio level. ========================================================================= Date: Fri, 9 Dec 2005 23:25:20 -0600 From: "Stephen Hicks, N5AC" Subject: RE: MARS MOD... > Steve - > Are these "diodes" - surface mount item or do they have > leads at each end? They almost look like flat surface > devices that are just wave soldered or something, in > place. Or are there leads at the 2 ends of each > square body? The diodes actually have very small flat leads sticking out under the device. They are very small and you can only see them once the device is up off the board. If you are good at soldering and have a decent low wattage iron, it should be no problem. Do not force anything as you can tear a pad off of the PCB. Although not probably a recommended method, I generally take the iron and hit either side of the diode back and forth till the device and the board are hot enough for the solder on one side to stay liquid as I move to the other side. You have to move fast and be careful, but I use this method a lot on SMT microwave boards and it works for me. Steve, N5AC ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= ========================================================================= =========================================================================